Standard model features powder-coated door, front, and sides. Interior has 304 stainless steel on door liner, top, bottom, back and sides. Exterior is galvanized heavy-duty steel or alumnum construction for long term corrosion free appearance. Changes to color possible with optional upgrade. Heavy-duty casters included as standard.
Optional model availability to change construction materials to aluminum or higher end grades of stainless steel available.
3 stainless steel wire shelves are standard. Shelves capable of supporting up to 100 lbs of evenly distributed weight.
Full height shelf support pilasters, with double oblong holes on 1/2″ centers. Pilasters made of stainless steel. Four (4) chrome plated, stainless steel shelf clips to be included for each shelf.
Unit is supplied with shut down capability upon attaining set temperature. Prevents runaway temperature from unintended eradication. Can be bypassed for intended decontamination.
Positive magnetic seal. Reversible.
Entire cabinet structure and doors insulated using 2″ urethane foam.
Top mounted, thermoelectric cooling system. Peltier based technology is solid state, highly efficient, reliable, and provides minimal vibration.
Semi-Redundant cooling capability.
Cooling surfaces can be made to act as dehumidifying modules at 25°C/60%RH and 30°C/65%RH.
Unit completely pre-wired at factory, and ready for final connection to a 115/60/1 phase – 15 amp dedicated (recommended) outlet.
A cord and plug set is included.
A sole use circuit is recommended.
Insect Rearing Chambers – IN034
The IN series chambers are designed with insect rearing as the primary application, but can be used for other research studies as well. Our IN series chambers are widely used among Drosophila and Mosquito researchers and offer state of the art technology for pursuing various research studies.
The IN034 is single-door incubator providing extra cubic feet designed for maximum capacity while still allowing passage through most commercial doorways.
Popular options include humidity control, lighting, timed lighting, chart recorder and TraceLock electronic/audit capable locks.
The IN series was introduced in 2003 as the first commercially manufactured large capacity Peltier-cooled insect rearing chamber. Thousands of IN series insect rearing chambers are presently in use by research companies around the world. The advantages of these chambers for insect rearing include:
Reliable Cooling Redundancy
Each IN series chamber includes multiple, independent thermoelectric cooling units. The 7 year warranty on cooling components and the ability of our chambers to maintain temperature even if the chamber suffers multiple failures is unmatched by any other refrigeration-based chamber.
Due to the omission of all refrigeration equipment on these models, refrigeration technicians are not required during chamber servicing. Refrigerated insect rearing chambers are not only costly to service, but can require days to service properly. Nearly every component of thermoelectric-based chambers can be serviced within minutes with basic tools. For instance, the ultrasonic humidifier is capable of being removed and reinstalled in less than a minute and operates on non-hazardous 24 volts.
Superior Control and Uniformity
The optional ultrasonic humidification system provides excellent humidity control and avoids hot spots seen during chamber mapping of steam boiler equipped chambers. Thermoelectric cooling and automatic switching system from cooling to heating control provide consistent results throughout the available temperature range. Standard control at the sensor in these chambers is ±0.2°C and ±0.3%RH.
Greatly Reduced Direct and Indirect Energy Loads
The IN Series chambers utilize less energy than comparable insect rearing chambers and introduce less impact upon building cooling systems. This efficiency “dual benefit” allows our chambers to be located in spaces unsuitable for other chambers. Electrical energy savings by the IN Series vs. steam boiler equipped chambers can easily amount to hundreds or even thousands of dollars saved per year.
Wiely Proven, Non-Proprietary Controllers
Standard controllers for the IN Series are manufactured by Fuji Electric and are ideal for insect rearing chambers. Unlike many proprietary controllers, this controller is commercially available and proven in tens of thousands of installations. Standard functions include: autotuning, fuzzy logic, PID control, programmable alarms, calibration capability, offset capability, etc. A touchscreen control interface is optional. Other controller manufacturers are also supported (Watlow, Allen Bradley etc.)
The IN chambers utilize quiet and highly efficient DC fans. Locating these chambers in laboratory workspaces is a viable option.
- Chart Recorder
- Data Loggers
- Timed Lighting
- Bench-Top Chamber Capable of Being Stacked
- Ultrasonic Humidification
Services and Warranties
We offer 24 hour technical support throughout the lifetime of your chamber. In addition to standard warranties, we also offer extended warranties for cooling components, parts and labor. We also provide qualifications, validations and preventive maintenance services at an additional cost. Please ask for a quote.