877-783-6774 314-534-3111
Architects Technical Support Request A Quote
Darwin Chambers
877-783-6774 314-534-3111

Insect Rearing Chambers – IN030

Request a Quote View Warranty

Insect Rearing Chambers – IN030

laboratory-incubator-te030-closed-small
laboratory-incubator-te030-open-small
Cabinet Construction
  • Stainless model has stainless steel front door, and sides on exterior. Interior is stainless steel side walls, back, floor, ceiling, and door liner. This unit includes LED interior lighting.
  • Standard model features stainless door, front, and brushed aluminum sides. Interior has coated aluminum side walls, door liner,and back with stainless steel floor and ceiling.
  • 2″ I.D access port with access port cover and insulation plug located on side wall of the chamber.
Doors
  • Positive seal, self-closing doors (gravity cam-lift) with 120 degree stay open feature. Door gasket removal and installation is tool-less. Glass door models feature double pane,”Low-E” glass.
Insulation
  • Entire cabinet structure and doors insulated using foamed-in-place CFC-free polyurethane foam.
Shelving
  • Wire shelves (3 per door) available in stainless steel or PVC coated. Shelves capable of supporting up to 150 lbs. Gray PVC coated shelves are standard.
  • Full height shelf support pilasters, with double oblong holes on 1/2″ centers. Pilasters made of the same material as cabinet interior. Four (4) chrome plated, stainless steel shelf clips to be included for each shelf.

Downloads

Download Specification
Cooling System
  • Top mounted, thermoelectric cooling system. Peltier based technology is solid state, highly efficient, reliable, and provides minimal vibration.
  • Semi-Redundant cooling capability
  • Cooling surfaces act as dehumidifying modules at 25°C/60%RH and 30°C/65%RH
Electrical Characteristics
  • Unit completely pre-wired at factory, and ready for final connection to a 115/60/1 phase – 15 amp dedicated (recommended) outlet. Unit runs approx. 4.6 RLA under test conditions.
  • A cord and plug set is included.
  • A sole use circuit is recommended.
Emergency Shut Down
  • Unit is supplied with shut down capability upon attaining set temperature.
  • Prevents runaway temperature from unintended eradication. Can be bypassed for intended decontamination.

Popular options include humidity control, glass door, chart recorder, and timed lighting (LED, T8, T5 etc.).

Features

IN Series

The IN series was introduced in 2003 as the first commercially manufactured large capacity Peltier-cooled insect rearing chamber. Thousands of IN series insect rearing chambers are presently in use by research companies around the world. The advantages of these chambers for insect rearing include:

Reliable Cooling Redundancy

Each IN series chamber includes multiple, independent thermoelectric cooling units. The 7 year warranty on cooling components and the ability of our chambers to maintain temperature even if the chamber suffers multiple failures is unmatched by any other refrigeration-based chamber.

Serviceability

Due to the omission of all refrigeration equipment on these models, refrigeration technicians are not required during chamber servicing. Refrigerated insect rearing chambers are not only costly to service, but can require days to service properly. Nearly every component of thermoelectric-based chambers can be serviced within minutes with basic tools. For instance, the ultrasonic humidifier is capable of being removed and reinstalled in less than a minute and operates on non-hazardous 24 volts.

Superior Control and Uniformity

The optional ultrasonic humidification system provides excellent humidity control and avoids hot spots seen during chamber mapping of steam boiler equipped chambers. Thermoelectric cooling and automatic switching system from cooling to heating control provide consistent results throughout the available temperature range. Standard control at the sensor in these chambers is ±0.2°C and ±0.3%RH.

Greatly Reduced Direct and Indirect Energy Loads

The IN Series chambers utilize less energy than comparable insect rearing chambers and introduce less impact upon building cooling systems. This efficiency “dual benefit” allows our chambers to be located in spaces unsuitable for other chambers. Electrical energy savings by the IN Series vs. steam boiler equipped chambers can easily amount to hundreds or even thousands of dollars saved per year.

Widely Proven, Non-Proprietary Controllers

Standard controllers for the IN Series are manufactured by Fuji Electric and are ideal for insect rearing chambers. Unlike many proprietary controllers, this controller is commercially available and proven in tens of thousands of installations. Standard functions include: autotuning, fuzzy logic, PID control, programmable alarms, calibration capability, ramp/soak, offset capability, etc. A touchscreen control interface is optional. Other controller manufacturers are also supported (Watlow, Allen Bradley etc.)

Quiet Operation

The IN chambers utilize quiet and highly efficient DC fans. Locating these chambers in laboratory workspaces is a viable option.

Options Available

  • Chart Recorder
  • CO2
  • Data Loggers
  • Timed Lighting
  • Bench-Top Chamber Capable of Being Stacked
  • Dryers
  • Ultrasonic Humidification
  • Full swinging interior glass door (034)

    • Services and Warranties

    We offer 24 hour technical support throughout the lifetime of your chamber. In addition to standard warranties, we also offer extended warranties for cooling components, parts and labor. We also provide qualifications, validations and preventive maintenance services at an additional cost. Please ask for a quote.